Showing results: 61 - 75 of 820 items found.
-
Intepro Systems
Introducing the Procyon ATE System! When it comes to ATE Test Systems for a for low- to high-volume production, Intepro has the testing power you require to be successful. For more than three decades, Intepro Systems has designed, built and integrated power supply test equipment for the world’s largest and smallest power supply manufacturers.
-
-
Shanghai Jiuzhi Electric Co., Ltd.
SGV Series DC test systems are used to test components and complete systems found in electrical power supply system what operate on DC voltage. Samgor DC voltage test systems can be implemented for tests with highest voltages according to IEC 60060-1.
-
Kokusai Co., Ltd.
This test machine is a tire wear test device that employs an electric servomotor power circulation system.
-
Digatron Power Electronics
The PowerNet Tester (BNT) is designed to test batteries, ultracaps and all other types of electrochemical power sources for 14 V and 42 V power net systems. Designed to test vehicle system batteries for 14V and 42V power net systems. But they may also be used for testing all other types of electrochemical power sources just by setting the required current and voltage values.
-
P-Series -
Keysight Technologies
The N8262A is a compact and slim LXI-compliant P-Series modular power meter. The N8262A helps you to reduce your test system size and enables LAN-based automated power measurements. Owing to LXI test standardization and its interoperability with existing test assets, your system can be up and ready in no time.
-
Chroma Systems Solutions, Inc.
Power conversion testing for automated test systems, LED drivers, power supply testing, battery testing, and much more.
-
ECO-Vibe neo -
EMIC Corporation
ECO-Vibe neo has been designed for an eco-friendly vibration test system. The test conditions with a vibration test system depends on a unit under test. Generally, the exciting force required for performing a vibration test can be calculated by the product of mass (e.g. test article, jig, table, etc.) and test acceleration. But, when the required exciting force is smaller than the maximum rated exciting force of the vibration test system, the field power supply that the constant current has to be continuously provided to produce the DC magnetic field constitutes a large part of power consumption compared with the drive power for the moving element. ECO-Vibe neo can reduce the power consumption by choosing the exciting force in this case. In addition, you can enjoy a reduction merit of the running cost from the first year when the system is introduced because initial cost is zero.
-
Yangzhou Power Electric Co., Ltd
High current test systems are used to test the thermal stability of equipment and components. The test system induces a current in the test object causing it to heat up.The system can perform the heat cycle testing for power cables type test and pre-qualification test according to IEC 60840, and IEC 62067 etc. Based on pre-qualification test needs, test system is divided into two parts: test sample loop and simulation temperature loop.
-
Shanghai Guantu Technology Co., Ltd.
The high (medium) voltage TOV tester is used for transient overvoltage tests caused by faults in high and medium voltage systems such as surge protectors (SPDs), and can also be used for other scientific research tests.standardGB/T 16927-1997 High voltage test technology.GB18802.1-2011 Surge protective device (SPD) for low-voltage power distribution system Part: Performance requirements and test methods.IEC61643-1:2005 (Surge protective devices connected to low-voltage power distribution systems part 1: Performance requirements and testing methods)TOV fault test equipment1. Three-phase isolation test transformer2. Single-phase test transformer3. Low voltage switchgear4. Power controller5. Test voltage and current measurement6. Sample box
-
Yelo Ltd.
The low power series of burn-in and life test systems are designed to test the reliability of low power laser diodes up to 1 Amp in current. The modular design means they can test up to 2,048 lasers, however due to the flexibility of the system, it can be adapted to suit both low volume R&D environments and high volume production environments.
-
ipTEST Limited
ipTEST now offers a range of multi-prober test systems with increased productivity and increased capability for power discrete wafer testing. Perform power discrete wafer testing and Known Good Die (KGD) tests.
-
N6700 MPS -
Acery Technologies
N6700 MPS has 16 different DC power supply modules, so test system designers can use these modules according to their specific test requirements to establish 1 to 4 channel DC power supply system. In the requirements of speed and accuracy of the occasion to invest in high-performance output, and for the general requirements of the DC power supply to buy basic performance output.
-
WA-BMS-3NE -
Xiamen WinAck Battery Technology Co., Ltd.
The battery BMS test system can be applied to the integrated test of 1S~100S power lithium-ionbattery pack BMS with LMU and BMCU modules, such as the BMS performance andHILL test.
-
UC8728 -
UC Instruments, Corp.
UC INSTRUMENTS UC8728 4/8 CHANNEL OPTICAL MULITIPORT POWER METER are PC control multiport passive components power meter test system and offer superior performance for the test of multichannel DWDM, WSS, ROADM, AWG & PLC components and modules, optical amplifiers, DWDM system and other general purpose of multiport fiber optical test and measurement applications. The system can be integrated with tunable laser source, optical attenuator & PDL controller provides a high performance passive components and modules automatic test system platform.